#CIJParty 2015 – Tutorial: Plastic Bottle Cuff Bracelet

Contributor post by Alicia of AliciasFindings

 “Tutorial for Plastic Bottle Cuff Bracelet” by Dawn Whitehand from DeeDeeDeesigns

Introduction

As an Etsy seller I love making jewellery and am passionate about upcycling, so this project combines both – we are making a cuff bracelet from plastic bottles decoupaged with newspaper, decorative papers and whatever extra adornments inspire you.dawn-whitehand_002

Materials Used

katherine-gorge-015_1_1

katherine-gorge-011_4_1

Scissors

craft knife/scalpel

ruler

PVA/craft glue

shallow dish for PVA

container of water

(for the above two I use a takeaway container – I use the lid for the PVA & the base for the water)

skewer

stiff bristled paint brushes – a range of small to medium sizes

varnish – acrylic, spray, polyurethane

plastic bottles – a range of sizes and textures

newspaper

AND a SELECTION of coloured paper, tissue paper, paper doilies, gift paper, stamps, calendars, maps, greeting cards, original drawings, children’s drawings, photocopies (not inkjet prints as they may run) and anything else you may think of!

Optional Adornments

buttons

sequins

beads

jute

ribbon

cabochons

wool offcuts

embroidery cotton offcuts

and whatever else inspires you!!

katherine-gorge-001_8_1

katherine-gorge-003_7_1

Tutorial Directions

Got all your ‘ingredients’? What’s next….

Choose a plastic bottle that, when cut, will fit around your wrist – be creative – it doesn’t have to be a round bottle, and if it is too big this could be an opportunity to add fasteners (buttons, etc) at the end.

Using your craft knife carefully cut (away from yourself) a portion of the bottle depending on how wide your want your cuff bracelet to be. If you want your end to be rounded or curved use some scissors to trim the square ends. I kept mine square as this is easier to fold your decoupage ends neatly and tightly.

tearing-paper

reserved-paper

The first three layers of your cuff will be built up using newspaper strips – use newsprint as this will be covered up – unless of course you want newsprint or certain words to feature in your bracelet – in this case reserve those pieces of newspaper for later layers.

Tear the newspaper layers using a ruler, rather than scissors, or simply go with the grain of the paper and tear them manually in about 2 cm wide strips although you won’t see these initial layers in the final product it does lend a textured surface beneath your final layer which will add to the final textural finish.

As you tear the newspaper look at both sides in case there are any colours or patterns you would like to reserve for the final layer.

Next pour a small amount, about the size of a ten-cent piece, of PVA into a shallow dish. Put your brush (approximately size 8) into the container of water and then place the brush in the PVA and mix.

katherine-gorge-016

the-olgas-039_1_1

Apply a generous amount to strips of paper, individually, and wrap diagonally around the plastic cuff until the entire surface is covered. (the water makes the paper more flexible and more easy to slide along the plastic). If there are any stubborn edges of paper that won’t lie flat use a small stiff bristled brush dipped in the water/pva mix to encourage it into place – until it does what it is told! The skewer can also be used as a mini rolling-pin to rill any bubbles and surface irregularities out; it can also be used to reinforce any patterns or lines in the bottle (see above picture of plastic bottle with indented lines). If you want to retain these lines they will have to be reinforced by pushing each layer of paper while still wet into the grooves. Use the entire length of the skewer to do this by holding it in the groove and turning the cuff.

katherine-gorge-007_6_1

Allow to dry – it won’t take very long, but you could use a hair dryer or heater if you are feeling impatient!

Repeat the previous step three times, allowing each layer to dry, and on the final third layer we will finish off the ends of the cuff.

katherine-gorge-010_5_1

To do this tear a larger square of newspaper that can be folded around the cuff end, tucked in and then folded over the ends – like a square envelope.

As before, apply the water/PVA mix generously and if need be, use a small stiff bristled brush to coax it into place.

the-olgas-037_2_1

Now it is time to think about the final layer we want on the cuff – gather together any reserved bits of patterned newspaper you have, coloured paper, paper doilies, stamps, maps – whatever your vision entails – I have used coloured and patterned newspaper to finish my cuff, positioning the paper in strategic spots to attain the finish I desire.

Use the same method as above to diagonally wind your cuff with strips of paper and finish the ends with enveloped squares as above also…. you can repeat this multiple times in various parts of your cuff till you get the design / colour combination that you like. You can also finish with a final feature of a picture or row of stamps, etc across the centre of the cuff as a feature. Don’t worry about uneven layers as this adds to the textural feel of the cuff (unless you want a less textured look, then you can be more particular about your layers and the layout of paper strips).

Allow this final layer to dry.

To seal the decoupaged surface apply 4-5 layers of the water/PVA mix, allowing each layer to dry, with a final sealing of an acrylic, spray or polyurethane varnish – the reason this project only requires one layer of varnish is so that your cuff will remain flexible enough to put on and off.

dawn-whitehand_002

dawn-whitehand_001

Once your cuff is finished you can adorn it with blingy bits….my cuff was a little big for my wrist so I sewed buttons and leather thong onto it as fasteners to fit my wrist – or any size wrist – it is adjustable!

Conclusion

Below are pics of other examples where the bottles I used fitted my wrist so no fasteners were needed. I also made a choker and ring …. the ring was made from the screw top part of the button which I removed using a hack saw as it is thicker than the body of the bottle.

the-olgas-034_4_1

the-olgas-035_3_1

I hope you enjoyed this crafty tutorial, and have a great day with many more to come!

Facebook: https://www.facebook.com/deedeedeesignsaustralia

Twitter: https://twitter.com/deedeedeesigns

Instagram: https://instagram.com/dawnwhitehand

Google +: plus.google.com/u/0/+DawnWhitehand

Pinterest: https://www.pinterest.com/dawnwhitehand/

Website: dawnwhitehand.wordpress.com

For the next #CIJParty post please see main party post.

Advertisements

One thought on “#CIJParty 2015 – Tutorial: Plastic Bottle Cuff Bracelet

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s